Omega Vehicle Security OMB-NETSCAN 1500 User Manual Page 232
- Page / 256
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Registers, Data Formats, & Queries
Appendix D
D-8 NetScan User’s Manual
Binary Data Format
Only High/Low/Last (HLL) register and acquisition output data, may be in binary format. Binary formatted data
can be output in either highbyte/lowbyte or lowbyte/highbyte format.
Time/Date Stamp
If binary format is selected, the High/Low/Last register values will also include time/date stamps. When
outputting the High/Low/Last registers for either highbyte/lowbyte or lowbyte/highbyte, the time/date stamp will
have the following format:
hmstMDY
where each letter is a byte represented by:
h
hours
M
months
m
minutes
D
days
s
seconds
Y
years
t
tenths
A typical High/Low/Last will have the following binary format (each letter is a byte of data):
HHhmstMDYLLhmstMDYll
where:
HH
is high,
LL
is low, and
ll
is last
Counts Data Format
The Counts data format is a format that is characterized by an ASCII integer number from -32676 to +32676
that represents a compensated or raw value as it would be interpreted from the A/D converter. This value would
be dependent upon the channel type which has been specified for the channel in question.
Note: The Counts format closely follows the channel type that has been specified.
Example 1:
If channel 16 was type 1: (Type J TC with cold junction compensation and linearization) then the
Counts format output value for this channel would also be cold junction compensated and linearized.
Example 2:
If channel 16 was type 31: (Raw A/D data), then the Counts format output value for channel 16 would
also be raw.
Both temperature and volts readings will be represented by a bipolar 16-bit value of the form: +
xxxxx
.
Time/Date stamp format is
hmstMDY
, which is
the same as that specified for the binary data format.
The Counts format is both a valid input (
C
and
L
command) format and a valid output format (
R
,
R#
,
U4
,
U5
,
U8
,
U13
,
C?
and
L?
command queries).
- OMB-NETSCAN 1
- OMEGAnet 2
- On-Line Service 2
- Internet e-mail 2
- How To Use This Manual 3
- Table of Contents 4
- 6 Calibration 5
- 7 Hardware Setup 5
- Inspect Your System 7
- Check and Install Hardware 8
- Setup for Ethernet Operation 10
- NetScan and TCP/IP Addressing 14
- Protocol 14
- IP Address 14
- Sub-net Mask 14
- Gateway Address 14
- Configuration 15
- Connect Channel Signal Inputs 16
- DB50 Pin Descriptions 17
- Overview 19
- ChartViewNET, Basic Concepts 19
- Chartvw.cvw 20
- ChartViewNET Quick Start 21
- 1. Select Interface Device 24
- 2. Configure Chart Setup 25
- ChartView Toolbar Reference 27
- 4. Configure Acquisition 28
- 5. Review Configuration 29
- 8. Start Charts 30
- A Note In Closing 30
- General Description 31
- Operational Aspects 32
- Software and Hardware 33
- NetScan Specifications 33
- Channels 34
- Triggers 35
- Data Storage & Format 35
- Calibration 37
- Three Ways of Using ChartView 40
- 1) Waiting for Trigger 41
- Main Window 42
- Channel Information Region 44
- Status Indicator Region 45
- Main Window Toolbar 46
- Adding Channel 2 to Chart 1 48
- Adding a Chart to Group 1 51
- PostView post-acq data viewer 53
- Arm Acquisition 53
- Disarm 53
- Main Window Pull-Down Menus 54
- File Menu Note 55
- Link to Excel… 59
- Upload Data 59
- Acquisition 59
- Stop Upload 59
- Setup IEEE 488 61
- RS-232/422 61
- … Status 62
- Instrument Error 64
- Instrument 64
- Realtime Clock 64
- Bar Graph Meters 66
- Analog Meters 67
- Digital Meters 68
- Meter Toolbars 69
- Meter Pull-Down Menus 69
- Meters Configuration Menu 70
- Configuring a Meter 70
- Setup Window 71
- Acquisition Setup Dialog Box 74
- Acquisition Setup 76
- Data Destination Dialog Box 77
- Chart Setup Wizard 79
- PostView 83
- Introduction 84
- Starting PostView 85
- PostView Toolbar Items 86
- Menu Items 88
- Automatic Display Creation 90
- Display Configuration 91
- Editing a Display 92
- PostView 5-11 93
- Manually Creating a Display 94
- PostView Timebase 97
- Calibration 6 99
- &$87,21 100
- Hardware Protected RAM 100
- ScanCal Software Application 101
- Using ScanCal 102
- Interface Parameters 102
- Calibration Without ScanCal 103
- Calibration of Main Unit 104
- Gain Calibration of Main Unit 106
- Offset Calibration of Cards 108
- Cold Junction Calibration 115
- Hardware 7 119
- Rear Panel 120
- Power Aspects 121
- Memory Configuration 122
- Serial Port Pin Connectors 126
- (RS-232) 127
- (RS-422) 127
- Digital I/O Lines 128
- External TTL BNC Connectors 129
- Signal Conditioning Cards 129
- CSN14/TC/P 130
- CSN14/LV/ (T, B, & S) 132
- CSN14/HV/S 133
- CSN/Relay Card 134
- CSN/Relay Card Specifications 135
- 7-18 NetScan User’s Manual 136
- Automatic Channel Assignment 137
- Appendices 139
- A-ii NetScan User’s Manual 140
- API Commands 141
- Command Syntax 142
- Command Interpretation 143
- Command Summary 146
- Command Reference 150
- - Trigger On Command 151
- - Power-On Reset 154
- - Power-Up Settings 154
- - Time Stamping 155
- - Assign Alarm Output 156
- - Alarm Stamping 157
- - Configure Channels 158
- - Select Card 160
- - Set Relay Make Time 161
- - End Calibration Mode 161
- - Error Status Query 162
- - Set Data Format 163
- - Calibrate Channel Gain 166
- - Set Scan Interval 168
- - Digital Input Stamping 169
- - Enter Calibration Mode 171
- - Set Trigger Level 172
- - Set Measuring Mode 173
- - Set Event Mask 174
- - Set Digital Outputs 175
- - Program Trigger Times 176
- - Query 177
- - Set Query Terminator 178
- - Query Card Data 180
- - Read Buffered Data 181
- - Read Last Readings 182
- - Set Real Time Clock 182
- - User Status 185
- - Set User Terminator 189
- - Set Average Weight 189
- - Execute 190
- API Command Reference 192
- Appendix A 192
- A-52 NetScan User’s Manual 192
- Ethernet API Reference 193
- Appendix C 197
- Contents 197
- Memory Allocation 198
- Measuring Modes 199
- Normal Mode 200
- Configuration Requirements 202
- Channel Configuration 203
- Scan Configuration 205
- Acquisition Configuration 206
- Pre-Trigger State 207
- C-12 NetScan User’s Manual 208
- Trigger and Stop Events 209
- C-14 NetScan User’s Manual 210
- Time Stamping ( 211
- Alarm Stamping ( 211
- Digital Input Stamping ( 212
- With Digital Input Stamping: 213
- Also see Digital Input ( 213
- ) command in Appendix A 213
- Trigger Block Organization 214
- NetScan User’s Manual C-19 215
- Multiple Trigger Blocks 216
- NetScan User’s Manual C-21 217
- C-22 NetScan User’s Manual 218
- NetScan User’s Manual C-23 219
- C-24 NetScan User’s Manual 220
- Configuring Alarms 222
- Set Point Hysteresis 223
- Digital I/O Operation 224
- Appendix D 225
- HLL Register Contents 226
- Accessing HLL Registers 226
- Example 1: 227
- Example 2: 227
- Example 3: 228
- Example 4: 228
- Example 5: 228
- Data Format 229
- Data Output Formats 230
- Engineering Units Data Format 230
- Binary Data Format 232
- Counts Data Format 232
- Configuring Power-Up State 233
- Query (?) Commands 234
- U Status Commands 234
- Theory of Operation 236
- NetScan User’s Manual D-13 237
- Event Status Register 238
- Event Status Enable Register 238
- Status Byte Register 239
- Trigger Latency 241
- Trigger Overrun 241
- Buffer Overrun 241
- Real Time Clock 242
- NetScan Program Examples 243
- Appendix E 244
- E-2 NetScan User’s Manual 244
- ASCII Code Summary 245
- ASCII Code Details 247
- Appendix F 248
- F-4 NetScan User’s Manual 248
- NetScan Error Messages 249
- Appendix G 250
- G-2 NetScan User’s Manual 250
- Abbreviations 251
- Appendix H 252
- H-2 NetScan User’s Manual 252
- NetScan User’s Manual 254
- WARRANTY/DISCLAIMER 255
- RETURN REQUESTS/INQUIRIES 255
Related products and manuals for Measuring, testing & control Omega Vehicle Security OMB-NETSCAN 1500
(15 pages)© 2020, manymanuals.com. All rights reserved. | 0.249 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals